Furnace Ignitor Replacement: 5 Surprising Reasons It Fails

Close-up of a furnace hot surface ignitor.

A furnace ignitor can fail because it’s worn out, cracked, or getting the wrong voltage. Sometimes moisture or the wrong replacement part causes trouble. If your furnace won’t light, the ignitor is one of the first parts worth checking. But that doesn’t mean it’s always the problem.

It’s a cold morning, and your furnace just won’t heat the house. You can hear it trying to start, but there’s still no warm air. So, what’s going wrong? At Star Services Heating & Air Conditioning, we help North Georgia homeowners get their heat working again. Before you pay for furnace ignitor replacement, here’s what you should know.

What Does a Furnace Ignitor Actually Do?

Your gas furnace needs a way to light the burners. Many furnaces use a small part called a hot surface ignitor. It gets hot enough to light the gas when the furnace starts. Some systems use a spark instead. The parts look different, but both help start the heating process. Hot surface ignitors are made from materials that can take a lot of heat. Still, they’re not meant to last forever. If one breaks, the furnace may try to start a few times before giving up.

5 Reasons Your Furnace Ignitor Keeps Failing

HVAC technician holding old and new furnace ignitors during replacement inside an open gas furnace.

1. The Ignitor Has Simply Worn Out

Think about how many times your furnace starts during winter. Each time, the ignitor gets hot. Then it cools down once the heating cycle ends. After years of this, the heating element can weaken. Small cracks may form, and one day, it stops working.

There’s no exact age when every ignitor fails. Some last for years without trouble. Others wear out sooner, especially in furnaces that start and stop often. If your furnace is getting older and still has its original ignitor, normal wear is worth considering.

2. Something Is Wrong With the Electrical Supply

A new ignitor shouldn’t burn out after a few weeks. If yours does, the voltage or wiring may be the real problem. Different ignitors need different electrical supplies. Too much voltage can damage certain types. A bad connection or faulty control board can also stop the ignitor from working.

A technician may need to check:

  • The voltage reaching the ignitor
  • Loose or damaged wires
  • The furnace control board
  • The electrical connections

If the same part keeps failing, replacing it again without checking the power supply doesn’t make much sense.

3. Moisture or Dirt Has Gotten Inside

A little dust around your furnace isn’t unusual. But dirt near the burners can cause problems when the system tries to light. Moisture is another concern. If water reaches the wrong parts, it can damage the ignition system. Some hot surface ignitors are also sensitive to dirt or other substances on the heating element.

This doesn’t mean every dirty furnace has a bad ignitor. Sometimes the burner needs attention, while the ignitor works just fine. Keep the furnace area dry and free from clutter. Change dirty filters when needed. And don’t try to wipe the ignitor with a cloth or cleaning spray. It’s easy to break.

4. The Replacement Part Doesn’t Match Your Furnace

Here’s something that catches people out. Two ignitors can look almost identical and still have different electrical requirements. You might find a replacement online that looks just like the old one. It fits the bracket, the wires seem right, and everything looks fine. But if the part isn’t compatible, the furnace may not work as it should.

The furnace model number matters more than how the part looks. If an ignitor was recently replaced and the heating problem came back, check whether the correct part was installed. A new part isn’t always the right part.

5. The Ignitor Was Damaged While Being Fitted

Some hot surface ignitors are surprisingly easy to break. A small knock against the furnace cabinet can crack the heating element. Certain types also need careful handling to avoid contamination. Touching the heating surface may go against the manufacturer’s instructions.

The tricky part is that damage isn’t always obvious. You might see a crack, or the ignitor might look completely normal. Once the heating element is broken, cleaning or adjusting it won’t fix the damage. The part needs replacing.

How Can You Tell If Your Furnace Ignitor Is Bad?

Your furnace might make a clicking sound, try to start several times, or run without heating the house. Those are signs of an ignition problem, but they don’t tell you which part has failed. The point where the furnace stops working can help narrow things down.

What happensWhat could be wrong
Hot surface ignitor doesn’t glowBad ignitor, wiring, or control problem
Ignitor glows, but no flame appearsGas supply, gas valve, or burner issue
Burners light and then go outFlame sensor or flame-proving problem
Furnace runs for a while, then shuts offAirflow or overheating problem
Nothing happens when heat is called forThermostat, power, or safety control issue

A furnace with spark ignition won’t have a glowing ignitor, so the signs can differ. If your burners light but won’t stay on, our guide to furnace flame sensor problems may help you understand what’s happening.

When Is Furnace Ignitor Replacement Necessary?

If the ignitor is cracked or has failed an electrical test, replacement is usually the answer. There’s little point in trying to repair a broken heating element. But what if the ignitor isn’t getting power? That’s a different problem. The wiring, control board, or another furnace safety part may be at fault.

A qualified technician can check the ignition sequence and test the part. That way, you know whether a new ignitor will actually get the heat back on.

How Much Does Furnace Ignitor Replacement Cost?

The furnace ignitor replacement cost is often around $100 to $250, including professional labor. Some repairs can cost $150 to $450 or more, depending on the furnace and work needed. The part itself is only one part of the bill. You may also pay for diagnosis, labor, or other repairs.

Before agreeing to the work, ask:

  • Is the diagnostic fee included?
  • Does the price cover the part and labor?
  • Is the new ignitor covered by a warranty?
  • Are there any other problems that need fixing?

These are general US price ranges. Your actual cost in North Georgia will depend on the furnace and the repair.

Is Replacing a Furnace Ignitor a DIY Job?

You can buy a furnace ignitor online. But getting the right part and fitting it safely are two different things. The ignitor sits near gas burners and connects to electrical parts. It’s also easy to damage during installation. If you’re not familiar with furnace repairs, it’s better to leave this job to a qualified HVAC technician.

You can still check a few simple things before calling:

  • Is the thermostat set to heat?
  • Is the air filter badly clogged?
  • Are any vents blocked?
  • Has the furnace circuit breaker tripped?

If those checks don’t help, don’t keep resetting the furnace or opening its gas components. If you smell gas, leave the building and call your gas utility or emergency services from a safe place.

How Long Does a Furnace Ignitor Last?

Many hot surface ignitors last several years. How long yours lasts depends on the type, how often the furnace runs, and whether there are electrical problems. You don’t need to replace a working ignitor just because it’s old. But if your furnace has trouble lighting, it’s worth having the ignition system checked.

Can a Bad Furnace Ignitor Make the Furnace Blow Cold Air?

Yes. In some furnaces, the blower can run even when the burners haven’t lit. You may feel cool air coming through the vents instead of heat. The ignitor is one possible cause. Thermostat settings and other furnace faults can produce similar symptoms.

Need Furnace Ignitor Replacement in North Georgia?

Nobody wants to wake up to a cold house, especially when the furnace was working the night before. And nobody wants to pay for a new part only to find out it wasn’t the problem. At Star Services Heating & Air Conditioning, we provide heating repair services for homeowners in Alpharetta, Cumming, Gainesville, Duluth, Johns Creek, Buford, and nearby North Georgia areas.

Whether your furnace won’t light or keeps shutting down, we can inspect the system and find out what’s going wrong. We also offer emergency heating repair when you need help getting the heat back on. Contact Star Services to schedule a furnace inspection. Before you spend money on another ignitor, wouldn’t you rather know why the last one failed?

Leave a Comment